Technology » Find Out hear are What’s general steps for PCB clone?
What’s general steps for PCB clone ?
Many new and old customers want to know what is the general process and steps of PCB clone? Let’s give you a brief introduction:
- Step 1: Preparation
Get an exemplary circuit board and scan it as a backup before removing the components. Remove the higher part first, and then perform a second scan to record the image. Do the cleaning work before scanning to ensure that the IC model and the PCB characters are visible on the picture after scanning.
- Step 2: Disassemble components and make BOM.
Use a hot air gun to heat the component to be removed. The removal order is first the resistor, then the capacitor, and finally the IC. Before disassembling, It should prepare a form with recorded items such as tag, package, model, and value. After removing all the components, use a bridge to measure its value. After the measurement is completed, enter the data into the computer for archiving.
- Step 3: Remove the dirt on the surface
Remove the remaining tin dross on the PCB surface of the removed component. Pay attention to the electric iron temperature should not be too high not to burn the ink.
- Step 4: PCB clone
After scanning the surface image, it is determined as the top and bottom layers, respectively. First, package the components (including small screen printing, pad diameter, positioning holes, etc.). After all, parts are completed, place them in corresponding positions, and adjust them to match the original board.
Sand the surface with sandpaper to expose bright copper.
If it is a multi-layer board, take an 8-layer board as an example:
After one or eight layers have been copied, then one and eight copper layers are ground off. Two and seven layers are copied, then three and six layers, and finally, four or five layers are sufficient. During the operation, make sure that the base map’s size is correct and then adjust the PCB components’ position one by one so that they coincide entirely with the base map. - Step 5: Check
Using image processing software, combined with PCB drawing software and physical circuit connection, can make 100% accurate judgment.
In the traditional clone PCB method in the interview, if the non-destructive method is adopted, the circuit board is scanned by CT to obtain a projected image. Then a three-dimensional image is obtained using image reconstruction technology. Then It can get the pictures of each layer by correcting and layering.
Introduction of OROD PCB Copy Board,OROD PCB copy board is to clone the circuit board, make a prototype, exchange components, make a BOM list, and export the schematic diagram in the case of the existing PCB circuit board. The circuit board clone includes single-board cloning and the entire set — Circuit board clones, etc.
In the copying industry, OROD has more than ten years of practical experience. It has cloned and prototyped electronic circuit board samples from various industries. It has absolute control over the copying cycle control, rigorous technical research, and cost Advantage.
OROD PCB Studio, the company, continues to reform and innovate, improve the mechanism, and introduce new talents. It has always been a leader in the reverse technology research of electronic products; However, it has been imitated; it has never been surpassed.
The upgrading of today’s electronic products can be described as rapid; based on holding the traditional circuit board structure mode and basic circuits of the whole handheld computer, OROD PCB clone engineers are continually improving their R & D capabilities with the updating of electronic products; Fully ensured that the cloned product is 100% the same as the sample provided by the customer; it also reduces the copying cycle of products that have a lot of blind and buried holes, saving customers time and costs •
In the OROD copy PCB process, combining the most cutting-edge design software and process technology, we can create the perfect prototype for you; it can also generate various software format documents for you.
Such as: PowerPCB, Protel99 / Se, PAD200. Maybe your cloned product needs to generate schematic diagrams, B0M bill of materials, etc. We can also serve you throughout the process. Hou, if the product you want to clone is earlier from the factory, and the components have been discontinued, please find OROD. Our B0M engineers and mining engineers will solve the problem for you; Please also find OROD. Our copy board engineers and PCB design and commissioning engineers will guarantee to make 100% accurate schematics and perfect prototypes for you …